After IPv6 is introduced to the FTTH (bridging ONT) scenario, the service configuration
procedure is as shown in the following figure. When IPv6 is introduced, the configurations for security features and BTV multicast services on the OLT side are different from those of IPv4. Other configurations do not change.
NOTE
Texts in blue show the configuration difference between IPv6 and IPv4.
Procedure
Step 1 Configure LAG for upstream ports.
Configure upstream ports 0/19/0 and 0/19/1 into an aggregation group. Each member port in the aggregation group allocates packets based on the source MAC address. The working mode is LACP static aggregation.
huawei(config)#link-aggregation 0/19 0-1 ingress workmode lacp-static
Step 2 Configure GPON ONT profiles.
- Configure a DBA profile.
Create the same DBA profile for different types of services. Set the profile name to
ftth_dba, profile type to type3, assured bandwidth to 8 Mbit/s, and maximum bandwidth
to 20 Mbit/s.
huawei(config)#dba-profile add profile-name ftth_dba type3 assure 8192 max 20480
2. Configure an ONT line profile.
Create a GPON ONT line profile, named ftth, and bind it to the DBA profile ftth_dba.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#tcont 4 dba-profile-name ftth_dba
huawei(config-gpon-lineprofile-1)#gem add 11 eth tcont 4
huawei(config-gpon-lineprofile-1)#gem add 12 eth tcont 4
huawei(config-gpon-lineprofile-1)#gem add 13 eth tcont 4
huawei(config-gpon-lineprofile-1)#gem add 14 eth tcont 4
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
3. Configure an ONT service profile.
Create a GPON ONT service profile, named ftth. Configure the capability set of the ETH
port and POTS port to adaptive. Then the system automatically adapts to the ONT
according to the actual capability of the online ONT.
huawei(config)#ont-srvprofile gpon profile-name ftth
huawei(config-gpon-srvprofile-1)#ont-port eth adaptive pots adaptive
huawei(config-gpon-srvprofile-1)#commit
huawei(config-gpon-srvprofile-1)#quit
4. (Optional) Add an alarm profile. In this example, the default alarm profile is used, and
therefore the configuration of the alarm profile is not required.
Step 3 Add ONTs.
Connect two ONTs to GPON port 0/1/0. Set the ONT IDs to 1 and 2, SNs to
32303131D659FD40 and 6877687714852901, passwords to 0100000001 and 0100000002, discovery mode for password authentication to once-on, and management mode to OMCI. Bind the two ONTs to ONT line profile ftth and ONT service profile ftth.
There are two methods of adding an ONT: add an ONT offline and confirm an automatically discovered ONT.
- Add ONTs offline.
If the password of an ONT is known, run the ont add command to add an ONT offline.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont add 0 1 password-auth 0100000001 once-on no-aging
omci ont-lineprofile-name
ftth ont-srvprofile-name ftth
huawei(config-if-gpon-0/1)#ont add 0 2 password-auth 0100000002 once-on no-aging
omci ont-lineprofile-name
ftth ont-srvprofile-name ftth
- Confirm automatically discovered ONTs
If the password or SN of an ONT is unknown, run the port portid ont-auto-find command
in GPON mode to enable the ONT auto-discovery function of the GPON port. Then, run the ont confirmcommand to confirm the ONT.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#port 0 ont-auto-find enable
huawei(config-if-gpon-0/1)#display ont autofind 0
//After this command is executed, the information about all ONTs connected to
the GPON port through optical splitters is displayed.
huawei(config-if-gpon-0/1)#ont confirm 0 ontid 1 sn-auth 32303131D659FD40 omci
ont-lineprofile-name
ftth ont-srvprofile-name ftth
huawei(config-if-gpon-0/1)#ont confirm 0 ontid 2 sn-auth 6877687714852901 omci
ont-lineprofile-name
ftth ont-srvprofile-name ftth
NOTE
If multiple ONTs of the same type bound to the same line profile or service profile are connected to the same port, you can bulk add ONTs by bulk confirming automatically discovered ONTs to make configuration easier and more efficient. To do so, the preceding command can be modified as follows:
huawei(config-if-gpon-0/1)#ont confirm 0 all sn-auth omci ont-lineprofile-name
ftth ont-srvprofile-name ftth
- (Optional) Bind the alarm profile to the ONT.
The default profile 1 is used in this example.
huawei(config-if-gpon-0/1)#ont alarm-profile 0 1 profile-id 1
huawei(config-if-gpon-0/1)#ont alarm-profile 0 2 profile-id 1
Step 4 Check ONT status.
After an ONT is added, run the display ont info command to query the current status of the ONT. Ensure that Config flag of the ONT is active, Run State is online, Config state is normal, and Match state is match.
huawei(config-if-gpon-0/1)#display ont info 0 1
———————————————————————
F/S/P : 0/1/0
ONT-ID : 1
Control flag : active //Indicates that the ONT is
activated.
Run state : online //Indicates that the ONT goes online
successfully.
Config state : normal //Indicates that the configuration state of the
ONT is normal.
Match state : match //Indicates that the capability profile bound to
the ONT is consistent with the actual capability of the ONT.
…//The rest of the response information is omitted.
When Config state is failed, Run state is offline, or Match state is mismatch:
- If Control flag is deactive, run the ont active command in GPON mode to activate the ONU.
- If Run state is offline, a physical line may be broken or the optical module may be damaged.
Check the line and the optical module.
- If Config state is failed, the configured ONU capability exceeds the actual ONU capability.
In this case, run the display ont failed-configuration command in the diagnose mode to
check the failed configuration item and the failure cause. Then, rectify the fault accordingly.
- If the ONU does not match, that is, Match state is mismatch, the port types and number of ports undermatch the actual port types and number of ports supported by the ONU. In this case, run the display ont capability command to query the actual capability of the ONU, and then select one of the following modes to modify the ONU configuration:
– Create a proper ONU profile according to the actual capability of the ONU, and then run
the ont modify command to modify the configuration data of the ONU.
– Modify the ONU profile according to the actual capability of the ONU and save the
modification. Then, the ONU automatically recovers the configuration successfully.
Step 5 Configure the traffic profile for the HSI service.
huawei(config)#traffic table ip name ftth_hsi cir 4096 priority 0 priority-policy
local-setting
Step 6 Configure the service port for the HSI service.
Table 1 Scenario plan
- Scenario 1:
Configure the mapping between a GEM port and a VLAN. The service flow of C-VLAN
1001 is mapped to GEM port 14 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#gem mapping 14 0 vlan 1001
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the PC
through Ethernet port 1, add Ethernet port 1 to VLAN 1001 in the ONT service profile.
huawei(config)#ont-srvprofile gpon profile-name ftth
huawei(config-gpon-srvprofile-1)#port vlan eth 1 1001
huawei(config-gpon-srvprofile-1)#commit
huawei(config-gpon-srvprofile-1)#quit
Configure the native VLAN of the ONT port. Set the native VLAN ID of Ethernet port 1 to 1001.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont port native-vlan 0 1 eth 1 vlan 1001
huawei(config-if-gpon-0/1)#ont port native-vlan 0 2 eth 1 vlan 1001
huawei(config-if-gpon-0/1)#quit
Create an Internet access service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 100.
huawei(config)#vlan 100 smart
huawei(config)#vlan attrib 100 stacking
huawei(config)#port vlan 100 0/19 0
Create service flows. Set the service VLAN to 100, GEM port ID to 14, and user VLAN to
1001. Use traffic profile ftth_hsi.
huawei(config)#service-port vlan 100 gpon 0/1/0 ont 1 gemport 14 multi-service
user-vlan 1001 tag-transform translate-and-add inner-vlan 1010 inbound traffic- table name ftth_hsi outbound traffic-table name ftth_hsi
huawei(config)#service-port vlan 100 gpon 0/1/0 ont 2 gemport 14 multi-service
user-vlan 1001 tag-transform translate-and-add inner-vlan 1011 inbound traffictable
name ftth_hsi outbound traffic-table name ftth_hsi
- Scenario 2:
Configure the mapping between a GEM port and an Ethernet port on the ONT. Map the
service flow of Ethernet port 1 to GEM port 14 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#mapping mode port
huawei(config-gpon-lineprofile-1)#gem mapping 14 0 eth 1
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Configure the ONT packet processing mode. If the ONT is connected to the PC through
Ethernet port 1, In the ONT service profile, set the packet transmission mode to TAG
transparent transmission for Ethernet port 1.
huawei(config)#ont-srvprofile gpon profile-name ftth
huawei(config-gpon-srvprofile-1)#port vlan eth 1 transparent
huawei(config-gpon-srvprofile-1)#commit
huawei(config-gpon-srvprofile-1)#quit
Create an Internet access service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 100.
huawei(config)#vlan 100 smart
huawei(config)#vlan attrib 100 stacking
huawei(config)#port vlan 100 0/19 0
Create service flows. Set S-VLAN ID to 100 and GEM port ID to 14. Use traffic profile
ftth_hsi.
huawei(config)#service-port vlan 100 gpon 0/1/0 ont 1 gemport 14 multi-service
user-vlan untagged tag-transform add-double inner-vlan 1001 inbound traffictable
name ftth_hsi outbound traffic-table name ftth_hsi
huawei(config)#service-port vlan 100 gpon 0/1/0 ont 2 gemport 14 multi-service
user-vlan untagged tag-transform add-double inner-vlan 1002 inbound traffictable
name ftth_hsi outbound traffic-table name ftth_hsi
Step 7 Configure the traffic profile for the voice service.
huawei(config)#traffic table ip name ftth_voip cir off priority 5 priority-policy
local-setting
Step 8 Configure the VLAN translation policy and service flows for the voice service.
1. Perform this step in the bridging ONT (single VLAN tag) scenario.
Table 2 Data plan
Configure the mapping relationship between a GEM port and a VLAN. The service flow
of user VLAN 300 is mapped to GEM port 12 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#gem mapping 12 2 vlan 300
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN
300.
huawei(config)#vlan 300 smart
huawei(config)#port vlan 300 0/19 0
Create service flows. Set the service VLAN to 300, GEM port ID to 12, and user VLAN
to 300, and use traffic profile ftth_voip.
huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multi-service
user-vlan 300 inbound traffic-table name ftth_voip outbound traffic-table
name ftth_voip
huawei(config)#service-port vlan 300 gpon 0/1/0 ont 2 gemport 12 multi-service
user-vlan 300 inbound traffic-table name ftth_voip outbound traffic-table
name ftth_voip
2. Perform this step in the bridging ONT (double VLAN tags) scenario.
Table 3 Data plan
Configure the mapping relationship between a GEM port and a VLAN. The service flow
of user VLAN 3001 is mapped to GEM port 12 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#gem mapping 12 2 vlan 3001
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN
300.
huawei(config)#vlan 300 smart
huawei(config)#vlan attrib 300 stacking
huawei(config)#port vlan 300 0/19 0
Create service flows. Set the service VLAN to 300, GEM port ID to 12, and user VLAN
to 3001, and use traffic profile ftth_voip.
huawei(config)#service-port vlan 300 gpon 0/1/0 ont 1 gemport 12 multiservice
user-vlan 3001 tag-transform default inbound traffic-table name ftth_voip
outbound traffic-table name ftth_voip
huawei(config)#service-port vlan 300 gpon 0/1/0 ont 2 gemport 12 multiservice
user-vlan 3001 tag-transform default inbound traffic-table name ftth_voip
outbound traffic-table name ftth_voip
Step 9 Configure ONT voice service profiles.
ONT voice service profiles include the interface common profile, MGC interface profile, and POTS port profile.
- Interface common profile: saves common attributes of an ONT voice interface, including the fax mode, fax/modem negotiation mode, and priority of the coding and decoding mode.
- MGC interface profile: saves the IP address or domain name of the MGC, protocol port ID of the MGC transport layer to which the MG interface belongs, and DSCP priority of media packets.
- POTS port profile: saves physical attributes of a POTS port on an ONT, including the
impedance, transmitting gain, receiving gain, and signaling type of the POTS port.
1. Configure an interface common profile.
Run the display ont-mg-attribute-profile command to query the existing interface
common profile in the system. If the existing interface common profile in the system does
not meet the requirements, run the ont-mg-attribute-profile add command to add an
interface common profile.
In this example, the default interface common profile, namely interface common profile 1
is used.
2. Configure an MGC interface profile.
Run the display ont-mgc-profile command to query the existing MGC interface profile in
the system. If the existing MGC interface profile in the system does not meet the
requirements, run the ont-mgc-profile add command to add an MGC interface profile.
Create MGC interface profile 2, set the IP address of the MGC to 200.200.200.200, and
use default values for other parameters.
huawei(config)#ont-mgc-profile add profile-id 2 primary-mgc 200.200.200.200
3. Configure a POTS port profile.
Run the display ont-pots-profile command to query the existing POTS port profile in the
system. If the existing POTS port profile in the system does not meet the requirements, run the ont-pots-profile add command to add a POTS port profile.
In this example, the default POTS port profile, namely POTS port profile 1 is used.
Step 10 Configure the IP addresses of ONT H.248 users.
For ONT 1 and ONT 2, configure the IP address obtaining mode to the dhcp mode, set the
management VLAN to VLAN 20, and use default values for other parameters.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont ipconfig 0 1 dhcp vlan 20
huawei(config-if-gpon-0/1)#ont ipconfig 0 2 dhcp vlan 20
Step 11 Configure H.248 PSTN users.
1. Add an H.248 interface and apply an MGC interface profile to the interface.
For ONT 1 and ONT 2, set the MG ID to 1, apply MGC interface profile 2 to ONT 1 and
ONT 2, and use default values for other parameters.
If parameters of an MGC interface profile are changed, the MGC interface profile must be
reapplied to the ONT so that the changed parameters can take effect.
huawei(config-if-gpon-0/1)#if-h248 add 0 1 1 mgc-profile profile-id 2
huawei(config-if-gpon-0/1)#if-h248 add 0 2 1 mgc-profile profile-id 2
- Add PSTN users.
For ONT 1 and ONT 2, create a PSTN user, set the MG ID to 1 (identical to the MG ID of
the H.248 interface), and set the physical terminal port ID to A0 and A1.
huawei(config-if-gpon-0/1)#mgpstnuser add 0 1 1 mgid 1 terminalid A0
huawei(config-if-gpon-0/1)#mgpstnuser add 0 2 1 mgid 1 terminalid A1
Run the display mgpstnuser attribute command to check whether the configuration of
the PSTN user is properly set.
huawei(config-if-gpon-0/1)#display mgpstnuser attribute 0 1 1
——————————————————————————
F/S/P : 0/1/0
ONT ID : 1
Port ID : 1
MG ID : 1
Terminal ID : A0
…//The rest of the response information is omitted.
huawei(config-if-gpon-0/1)#display mgpstnuser attribute 0 2 1
——————————————————————————
F/S/P : 0/1/0
ONT ID : 2
Port ID : 1
MG ID : 1
Terminal ID : A1
…//The rest of the response information is omitted.
Step 12 Apply ONT voice service profiles
After ONT voice service profiles are applied, if parameters in those profiles are changed, those profiles must be reapplied so that the changed parameters can take effect.
1. Apply an interface common profile.
Run the if-h248 attribute command to apply an interface common profile to an H.248
interface or configure the interface customized parameters, or run the ont-if-h248 batapply command to bulk apply the interface common profiles to H.248 interfaces. If you
use these two commands to apply the interface common profiles or configure the interface
customized parameters repeatedly, the last configurations take effect.
In this example, the default interface common profile, namely interface common profile 1
is used.
2. Apply a POTS port profile.
Run the pstnport electric command to apply a POTS port profile to an H.248 interface or
configure the interface customized parameters, or run the ont-pstnport electric batapply
command to bulk apply the POTS port profiles to H.248 interfaces. If you use these
two commands to apply the POTS port profiles or configure the interface customized
parameters repeatedly, the last configurations take effect.
In this example, the default POTS port profile, namely POTS port profile 1 is used.
Step 13 (Optional) Configure the H.248 user codec.
Run the mgpstnuser codec command to configure the H.248 user codec. The H.248 user codec will not be configured independently in this example.
Step 14 Configure the traffic profile for the IPTV service.
huawei(config)#traffic table ip index 8 cir off priority 4 priority-policy
local-setting
Step 15 Configure the VLAN translation policy and service port for the multicast service.
Configure the mapping relationship between a GEM port and an Ethernet port on the ONT. If the ONT is connected to the STB through Ethernet port 2, map the service flow of Ethernet port 2 to GEM port 13 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#mapping mode port
huawei(config-gpon-lineprofile-1)#gem mapping 13 1 eth 2
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the STB
through Ethernet port 2, add Ethernet port 2 to VLAN 1000.
huawei(config)#ont-srvprofile gpon profile-name ftth
huawei(config-gpon-srvprofile-1)#port vlan eth 2 1000
huawei(config-gpon-srvprofile-1)#multicast-forward untag
huawei(config-gpon-srvprofile-1)#commit
huawei(config-gpon-srvprofile-1)#quit
Configure the native VLAN of the ONT port. If the ONT is connected to the STB through
Ethernet port 2, the native VLAN ID is 1000.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont port native-vlan 0 1 eth 2 vlan 1000
huawei(config-if-gpon-0/1)#ont port native-vlan 0 2 eth 2 vlan 1000
huawei(config-if-gpon-0/1)#quit
Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 1000.
huawei(config)#vlan 1000 smart
huawei(config)#port vlan 1000 0/19 0
Create service flows. Set the service VLAN to 1000, GEM port ID to 13, and user VLAN to
untagged, and use traffic profile 8.
huawei(config)#service-port 1 vlan 1000 gpon 0/1/0 ont 1 gemport 13 multi-service
user-vlan untagged rx-cttr 8 tx-cttr 8
huawei(config)#service-port 2 vlan 1000 gpon 0/1/0 ont 2 gemport 13 multi-service
user-vlan untagged rx-cttr 8 tx-cttr 8
Step 16 Create an MVLAN and configure the IGMP version.
Set the IGMP version for the MVLAN to IGMP IPv6 v2.
huawei(config)#multicast-vlan 1000
huawei(config-mvlan1000)#igmp ipv6 version v2
This operation will delete all IPv6 programs with source IP addresses in the
current multicast VLAN
Are you sure to change current IGMP IPv6 version? (y/n)[n]:y
Command is being executed. Please wait…
Command has been executed successfully
Step 17 Configure a program library.
Set the mode for obtaining multicast programs to dynamic.
NOTE
You can set the mode for obtaining multicast programs to dynamic only when the IGMP mode is off.
huawei(config-mvlan1000)#igmp ipv6 mode off
Are you sure to close IGMP IPv6? (y/n)[n]:y
Command is being executed. Please wait…
Command has been executed successfully
huawei(config-mvlan1000)#igmp ipv6 match mode disable
Command has been executed successfully
(Optional) Set the address range for the dynamic programs. If you need to limit the address range of dynamic programs, perform this operation. For example, set the address range of dynamic programs to ff15::-ff15::ffff.
huawei(config-mvlan1000)#igmp ipv6 match group ipv6 ff15:: to-ipv6 ff15::ffff
Step 18 Set the IGMP IPv6 mode.
Select the IGMP IPv6 proxy mode.
huawei(config-mvlan1000)#igmp ipv6 mode proxy
Are you sure to change IGMP IPv6 mode? (y/n)[n]:y
Command is being executed. Please wait…
Command has been executed successfully
Step 19 Configure the IGMP upstream port.
Set the IGMP upstream port ID to 0/19/0 and working mode to default. Protocol packets are transmitted to all the IGMP upstream ports in the multicast VLAN.
huawei(config-mvlan1000)#igmp uplink-port 0/19/0
huawei(config-mvlan1000)#btv
huawei(config-btv)#igmp uplink-port-mode default
Are you sure to change the uplink port mode?(y/n)[n]:y
Step 20 Configure multicast users.
Add service ports 1 and 2 as multicast users.
huawei(config-btv)#igmp policy service-port 1 normal
huawei(config-btv)#igmp policy service-port 2 normal
huawei(config-btv)#igmp user add service-port 1
huawei(config-btv)#igmp user add service-port 2
huawei(config-btv)#multicast-vlan 1000
huawei(config-mvlan1000)#igmp multicast-vlan member service-port 1
huawei(config-mvlan1000)#igmp multicast-vlan member service-port 2
huawei(config-mvlan1000)#quit
Step 21 Configure the traffic profile for the VoD service.
huawei(config)#traffic table ip index 8 cir off priority 4 priority-policy
local-setting
Step 22 Configure the VLAN translation policy and service port for the VoD service.
Configure the mapping relationship between a GEM port and a VLAN. The service flow of user VLAN 1100 is mapped to GEM port 13 in the ONT line profile.
huawei(config)#ont-lineprofile gpon profile-name ftth
huawei(config-gpon-lineprofile-1)#gem mapping 13 4 vlan 1100
huawei(config-gpon-lineprofile-1)#commit
huawei(config-gpon-lineprofile-1)#quit
Configure the VLAN of the Ethernet port on the ONT. If the ONT is connected to the STB
through Ethernet port 2, add Ethernet port 2 to VLAN 1100.
huawei(config)#ont-srvprofile gpon profile-name ftth
huawei(config-gpon-srvprofile-1)#port vlan eth 2 1100
huawei(config-gpon-srvprofile-1)#commit
huawei(config-gpon-srvprofile-1)#quit
Configure the native VLAN of the ONT port. If the ONT is connected to the STB through
Ethernet port 2, the native VLAN ID is 1100.
huawei(config-if-gpon-0/1)#ont port native-vlan 0 1 eth 2 vlan 1100
huawei(config-if-gpon-0/1)#ont port native-vlan 0 2 eth 2 vlan 1100
huawei(config-if-gpon-0/1)#quit
Create a service VLAN and add an upstream port to it. Add upstream port 0/19/0 to VLAN 1100.
huawei(config)#vlan 1100 smart
huawei(config)#port vlan 1100 0/19 0
Create service flows. Set the service VLAN to 1100, GEM port ID to 13, and VLAN translation mode to transparent transmission, and use traffic profile 8.
huawei(config)#service-port 3 vlan 1100 gpon 0/1/0 ont 1 gemport 13 rx-cttr 8 txcttr
8 tag-transform transparent
huawei(config)#service-port 4 vlan 1100 gpon 0/1/0 ont 2 gemport 13 rx-cttr 8 txcttr
8 tag-transform transparent
Step 23 (Optional) Configure the PITP function for PPPoE.
huawei(config)#raio-mode common pitp-pmode
huawei(config)#pitp enable pmode
Step 24 (Optional) Configure the DHCP option function for IPoE.
huawei(config)#raio-mode common dhcp-option82 //For DHCPv4 packets
huawei(config)#dhcp option82 enable //For DHCPv4 packets
huawei(config)#raio-mode common dhcpv6-option //For DHCPv6 packets
huawei(config)#dhcpv6 option enable //For DHCPv6 packets
Step 25 Save the configuration on the OLT side.
huawei(config)#save
—-End
More related:
No comments:
Post a Comment