Function
This command is used to query the information of public switched telephone
network (PSTN) subscribers on the optical network terminal
(ONT).
Parameters
| Parameter | Description | Value |
|---|---|---|
| portid | Indicates the ID of the PON port on the ONT. | Numeral type. Range: varies with the PON port on the ONT. |
| ontid | Indicates the ID of the ONT. | Numeral type. Range: varies with the number of ONTs supported by the board. |
| ont-portid | Indicates the ID of the POTS port on the ONT. | Numeral type. Range: 1-255. |
Usage Guidelines
- Run the config command to enter global config mode, and then run the interface gpon command to enter GPON mode.
- Run the config command to enter global config mode, and then run the interface epon command to enter EPON mode.
- You can run the mgpstnuser add(ont) command to add PSTN subscribers.
Example
To query the information of PSTN subscribers on ONT 0 over the 0/3/0 port, do as follows:
huawei(config-if-gpon-0/3)#display mgpstnuser attribute { portid<U><0,7> }:0 { ontid<U><0,127> }:0 { <cr> | ont-portid<U><1,255> }:1 Command: display mgpstnuser attribute 0 0 1 ------------------------------------------------------------------------------ F/S/P : 0/3/0 ONT ID : 0 Port ID : 1 MG ID : 1 Terminal ID : A10 ------------------------------------------------------------------------------ Using MG value : enable Order1 Codec1 : G711A Packet period1 : 20ms Silence1 : off Order2 Codec2 : G711U Packet period2 : 20ms Silence2 : off Order3 Codec3 : G729 Packet period3 : 20ms Silence3 : off Order4 Codec4 : G722 Packet period4 : 20ms Silence4 : off ------------------------------------------------------------------------------ POTS State : Unlock ------------------------------------------------------------------------------ PtpSrvState : Normal PtpAdmState : Unlock HookState : OnHook CTPSrvType : Idle CTPSrvState : Initial Codes : G711U ------------------------------------------------------------------------------
System Response
- The system displays the queried result when the command runs successfully.
- The following table describes the parameters in the response to the
display mgpstnuser attribute 0 0 1 command.
Parameter Description F/S/P Indicates the shelf ID, slot ID, and port ID. ONT ID Indicates the ID of the ONT. Port ID Indicates the ID of the POTS port on the ONT. MG ID Indicates the index of the MG interface associated with the subscriber. Terminal ID Indicates the ID of the physical terminal used by PSTN subscribers. Using MG value Indicates whether to use codec data configured on the MG interface. Codec1 Indicates the codec type in the codec mode with priority 1. Packet period1 Indicates the packetization duration in the codec mode with priority 1. Silence1 Indicates the silence suppression configuration in the codec mode with priority 1. Codec2 Indicates the codec type in the codec mode with priority 2. Packet period2 Indicates the packetization duration in the codec mode with priority 2. Silence2 Indicates the silence suppression configuration in the codec mode with priority 2. Codec3 Indicates the codec type in the codec mode with priority 3. Packet period3 Indicates the packetization duration in the codec mode with priority 3. Silence3 Indicates the silence suppression configuration in the codec mode with priority 3. Codec4 Indicates the codec type in the codec mode with priority 4. Packet period4 Indicates the packetization duration in the codec mode with priority 4. Silence4 Indicates the silence suppression configuration in the codec mode with priority 4. POTS State Indicates the status of the port. Options:- LOCK: The port is locked.
- UNLOCK: The port is unlocked.
PtpSrvState Indicates the running status of the physical layer. Options:- Normal: The physical layer is operating properly.
- FAIL: The physical layer fails to operate.
PtpAdmState Indicates the management status of the physical layer. Options:- LOCK: The physical layer has been locked.
- UNLOCK: The physical layer has been unlocked.
HookState Indicates the hooking status of the port. Options:- ONHOOK: The port is in the on-hook state.
- OFFHOOK: The port is in the off-hook state.
CTPSrvType Indicates the session type. Options:- IDLEORNONE: No service is running.
- TWOWAY: The service is a two-party session.
- THREEWAY: The service is a three-party session.
- FAX: The service is a fax service.
- TELEM: The service is a telegraphy service.
- CONFERENCE: The service is a conference.
CTPSrvState Indicates the working status of the service. Options:- NONEORINITIAL: The service has been initialized.
- REGISTERED: The service has been registered.
- INSESSION: The service is in progress.
- RegFail-ICMP: The service fails to be registered because of ICMP errors.
- RegFail-TCP: The service fails to be registered because of TCP errors.
- RegFail-AUTH: The service fails to be registered because of the authentication failure.
- RegFail-Timeout: The service fails to be registered because of the registration timeout.
- ,RegFail-Server: The service fails to be registered because of server errors.
- InvFail-ICMP: The session fails to be initiated because of ICMP errors.
- InvFail-TCP: The session fails to be initiated because of the TCP errors.
- InvFail-AUTH: The session fails to be initiated because of the authentication failure.
- InvFail-Timeout: The session fails to be initiated because of the session establishment timeout.
- InvFail-Server: The session fails to be initiated because of server errors.
- PortNotconfigure: The port is not configured.
- CONFIGDONE: The service has been configured.
- DisabledBySwitch: The service port is disabled by the call server.
Codes Indicates the coding mode of the port service. Options:- G711ULAW: G711U
- RESERVED: Reserved
- GSM: GSM
- G723: G723
- DVI4: DVI4
- LPC: LPC
- G711ALAW: G711A
- G722: G722
- L16_2CHANNEL: L16,2channels
- L16_1CHANNEL: L16,1channel
- QCELP: QCELP
- CN: CN
- MPA: MPA
- G728: G728
- G729: G729
- INVAILDVALUE: -
- For more information about the error message that the system displays against a command entered with incorrect syntax
MORE BLOG:
No comments:
Post a Comment