Showing posts with label GPBD. Show all posts
Showing posts with label GPBD. Show all posts

Monday, February 6, 2017

How to Adding an IUA Link Set?

This topic describes how to add an IUA link set. When configuring the VoIP ISDN service(thunder-link supply GPFD, GPBD), you need to configure the IUA link to carry the Q.931 call signaling. Before adding an IUA link, you must add a corresponding link set. Otherwise, the link cannot be added.

Context

  • The system supports the configuration of a maximum of IUA link sets.
  • After a link set is configured successfully, it is in the deactivated state by default.

Procedure

  1. In global config mode, run the commandsigtran to enter the Sigtran mode.
  2. Run the iua-linkset add command to add an IUA link set.
  3. You can run the display iua-linkset attribute command to check whether the configured IUA link set information is the same as the data plan.

Example

Assume that the link set ID is 0, working mode of the link set is active/standby mode, pending duration is 20s, prefix of the IID is b/, IID generation mode is using the binary value that is automatically generated in ffsspp mode, namely, parameter 2. To add such an IUA link set, do as follows:
huawei(config)#sigtran


Related:
Posted by at No comments:
Labels: ,

Monday, January 23, 2017

IP Routing Basic Commands on debugging rm backup

Function

Using the debugging rm backup command, you can enable the debugging of RM backup.
Using the undo debugging rm backup command, you can disable the debugging of RM backup.
By default, the debugging of RM backup is disabled.

Format

debugging rm backup
undo debugging rm backup

Parameters

None

Modes

Privilege mode, GPBD,GPFD,ETHB

Level

Administrator level

Usage Guidelines

In general, if a standby board is inserted, batch backup is generated. After batch backup is generated, the real-time backup is generated if batch backup does not break. The batch backup covers only a part of data. The other parts of data are sent to the standby board through real-time backup, such as RM interface information.

Example

# Debug RM backup and view the process of RM backup.
huawei#debugging rm backup




More Blog:

How many Remote frame ( RSU with HABD ) can UA5000-PVM board support?
Posted by at No comments:
Labels: , ,

Sunday, January 22, 2017

The ONT Broadband Service Management of display ont-learned-mac

Function Description

This topic provides the commands related to the ONT broadband service configuration.

Function

This command is used to query the information about the MAC addresses learned on the ONT that is connected to a PON port. To query the information about the MAC addresses learned on the ONT for problem location, run this command.

Format

display ont-learned-mac frameid/slotid/portid ontid [ port-type ont-portid [ vlanid ] | wlan ]

Parameters

Parameter Description Value
frameid/slotid/portid Indicates the shelf ID/slot ID/port ID of a PON port. Character string type, a string of 5-15 characters.
ontid Indicates the ONT ID. Numeral type. Range: varies with the board type.
port-type Indicates the ONT port type. Enumerated type. Options: ETH.
ont-portid Indicates the ONT port ID. Numeral type. Range: 1-8.
vlanid Indicates the VLAN ID. Numeral type. Range: 1-4094.
wlan Indicates the WLAN query mode. -

Modes

Privilege mode, GPFD, GPBD

Level

Operator level

Usage Guidelines

When the MAC addresses learned on the ONT that is connected to a PON port are queried, the system displays a maximum of 1000 MAC addresses that are first learned.

Example

To query the MAC addresses learned on Ethernet port 2 on ONT 10 that is connected to PON port 0/3/3, do as follows:
huawei#display ont-learned-mac 
{ frameid/slotid/portid<S><Length 5-15> }:0/3/3
{ ontid<U><0,127> }:10
{ <cr>|port-type<E><eth,vdsl>|wlan<K> }:eth
{ ont-portid<U><1,8> }:2
{ <cr>|vlanid<U><1,4094> }: 
    
  Command:            
          display ont-learned-mac 0/3/3 10 eth 2
  -----------------------------------------------------------------        
  F/S/P  ONTID    ONT        ONT       MAC-ADDRESS       VLAN
                  port-type  port-ID
  -----------------------------------------------------------------        
  0/ 3/3  10    ETH       2       00e0-fc20-47b9       200
  0/ 3/3  10    ETH       2       00e0-fc20-47ba       200
  -----------------------------------------------------------------
  Total: 2
To query the MAC addresses learned in VLAN 200 on Ethernet port 2 on ONT 10 that is connected to PON port 0/3/3, do as follows:
huawei#display ont-learned-mac                 
{ frameid/slotid/portid<S><Length 5-15> }:0/3/3
{ ontid<U><0,127> }:10
{ <cr>|port-type<E><eth,vdsl>|wlan<K> }:eth
{ ont-portid<U><1,8> }:2
{ <cr>|vlanid<U><1,4094> }:200                            
                                                                                
  Command:                                                                      
          display ont-learned-mac 0/3/3 10 eth 2 200
  
  ---------------------------------------------------------------        
  F/S/P  ONTID    ONT        ONT       MAC-ADDRESS       VLAN
                  port-type  port-ID
  ---------------------------------------------------------------        
  0/ 3/3  10    ETH       2       00e0-fc20-47b9       200
  0/ 3/3  10    ETH       2       00e0-fc20-47ba       200
  ---------------------------------------------------------------
  Total: 2
To query the MAC addresses learned in VLAN 200 on Ethernet port 2 on ONT 10 that is connected to PON port 0/3/3, do as follows:
huawei#display ont-learned-mac                 
{ frameid/slotid/portid<S><Length 5-15> }:0/3/3
{ ontid<U><0,127> }:10
{ <cr>|port-type<E><eth,vdsl>|wlan<K> }:wlan                         
                                                                                
  Command:                                                                      
          display ont-learned-mac 0/3/3 10 wlan
  
  ---------------------------------------------------------------        
  F/S/P  ONTID    ONT        ONT       MAC-ADDRESS       VLAN
                  port-type  port-ID
  ---------------------------------------------------------------        
  0/ 3/3  10    WLAN       1       00e0-fc20-47b9       -
  0/ 3/3  10    WLAN       2       00e0-fc20-47ba       -
  ---------------------------------------------------------------
  Total: 2 
  Note: When the ONT port-type is WLAN, the ONT port-ID indicates WLAN SSID index

System Response

  • The system displays the queried result when the command runs successfully.
  • Parameter Description
    F/S/P Indicates the shelf ID/slot ID/port ID of the ONT.
    ONT ID Indicates the ONT ID.
    ONT port-type Indicates the ONT port type.
    ONT port-ID Indicates the ONT port ID.
    MAC-ADDRESS Indicates the queried MAC address.
    VLAN Indicates the VLAN ID.
    WLAN Indicates the WLAN query mode. 
More blog:
Posted by at No comments:
Labels: , ,

The ONT Broadband Service Management of display ont mac-count

Function Description

This topic provides the commands related to the ONT broadband service configuration

Function

This command is used to query the ONT MAC address learning table.

Format

display ont mac-count portid ontid

Parameters

Parameter Description Value
portid Indicates the ID of the GPON port where the ONT to be queried is located. Please see Differences Between Shelves.
ontid Indicates the ID of the ONT to be queried. Numeral type. Range: varies with the board type.

Modes

GPON mode, GPBD, GPFD

Level

Operator level

Usage Guidelines

  • Before running this command, run the config command to enter global config mode, and then run theinterface gpon command to enter GPON mode.
  • The ONT must be online and working properly.

Example

To query the MAC address learning table of the ONT whose ID is 0 under GPON port 0/3/0, do as follows:
huawei(config-if-gpon-0/3)#display ont mac-count                                
{ portid<U><0,7> }:0                                                            
{ ontid<U><0,63> }:0                                                            
                                                                                
  Command:                                                                      
          display ont mac-count 0 0                                             
  --------------------------------------------------                            
  F/S/P                    : 0/3/0   
  ONT-ID                   : 0                                                 
  ONT MAC count            : 0                                                  
  --------------------------------------------------

System Response

  • The system displays the queried result when the command runs successfully.
  • The following table describes the parameters in response to the display ont mac-count command.
    Parameter Description
    F/S/P Indicates the shelf ID, slot ID, and port ID.
    ONT-ID
    S    		 Indicates the ONT ID.
    ONT MAC count Indicates the number of the MAC addresses currently learned by the ONT.
More Blog:
Posted by at No comments:
Labels: , ,

Monday, December 26, 2016

Board Transparent Transmission Channel Commands on emac encrypt display portmode(debugging)

Function

This command is used to query the encryption mode of a specified PON port.

Format

emac encrypt display portmode { oltid }

Parameters

Parameter Description Value
oltid Indicates the port ID. Please see Differences Between Shelves.

Modes

Diagnose mode, GPBD, GPON 

Level

Operator level

Usage Guidelines

Before running this command, run the transparent on(diagnose) command to enter transparent transmission channel mode.

Example

To query the encryption mode of PON port 0, do as follows:
huawei(diagnose)%%emac encrypt display portmode
 { OLTID:<0..7>[0] }:0
EncryptionMode:    None

System Response

  • The system displays the queried result when the command runs successfully.
  • The following table describes the parameters in response to this command.
    Parameter Description
    EncryptionMode
    Indicates the encryption mode.
    • None: Indicates that the PON port is not encrypted.
    • AES128: Indicates the AES128 encryption mode.
    • Triple churning(CTC): Indicates the triple churning encryption mode.
More blog:
Posted by at No comments:
Labels: ,

Tuesday, December 20, 2016

EPON ONT Line Profile Configuration about dba-threshold

Function

The dba-threshold command is used to configure the queue threshold in the DBA queue set of the ONT line profile. To configure the queue threshold in the DBA queue set of the ONT line profile, run this command.
The undo dba-threshold command is used to delete the queue threshold in a specified DBA queue set.

Format

dba-threshold queue-set-index { q1 value | q2 value | q3 value | q4 value | q5 value | q6 value | q7 value | q8 value } *
undo dba-threshold queue-set-index

Parameters

Parameter Description Value
queue-set-index Indicates the index of a DBA queue set. Numeral type. Range: 1-3.
q1 value Indicates the threshold of DBA queue 1. Numeral type. Range: 0-65535.
q2 value Indicates the threshold of DBA queue 2. Numeral type. Range: 0-65535.
q3 value Indicates the threshold of DBA queue 3. Numeral type. Range: 0-65535.
q4 value Indicates the threshold of DBA queue 4. Numeral type. Range: 0-65535.
q5 value Indicates the threshold of DBA queue 5. Numeral type. Range: 0-65535.
q6 value Indicates the threshold of DBA queue 6. Numeral type. Range: 0-65535.
q7 value Indicates the threshold of DBA queue 7. Numeral type. Range: 0-65535.
q8 value Indicates the threshold of DBA queue 8. Numeral type. Range: 0-65535.

Modes

EPON ONT line profile mode, GPBD, HG8245H

Level

Operator level

Usage Guidelines

  • Run the config command to enter global config mode, and then run the ont-lineprofile epon command to enter EPON ONT line profile configuration mode.
  • You can run the display ont-lineprofile epon command to query the configured parameters.
  • For a DBA queue set, configure the thresholds for the queues in the ascending order one by one, and delete the thresholds for the queues in the descending order one by one.

Example

To configure the thresholds to 128, 256, and 512 respectively for queues 1, 2, and 3 in DBA queue set 1 of ONT line profile 10, do as follows:
huawei(config-epon-lineprofile-10)#dba-threshold                                 
{ queue-set-index<U><1,3> }:1                                                   
{ q1<K>|q2<K>|q3<K>|q4<K>|q5<K>|q6<K>|q7<K>|q8<K> }:q1                          
{ value<U><0,65535> }:128                                                       
{ <cr>|q2<K>|q3<K>|q4<K>|q5<K>|q6<K>|q7<K>|q8<K> }:q2                           
{ value<U><0,65535> }:256                                                       
{ <cr>|q3<K>|q4<K>|q5<K>|q6<K>|q7<K>|q8<K> }:q3                                 
{ value<U><0,65535> }:512                                                       
{ <cr>|q4<K>|q5<K>|q6<K>|q7<K>|q8<K> }:                                         
                                                                                
  Command:                                                                      
          dba-threshold 1 q1 128 q2 256 q3 512
To delete the queue threshold in DBA queue set 1 of ONT line profile 10, do as follows:
huawei(config-epon-lineprofile-10)#undo dba-threshold                            
{ queue-set-index<U><1,3> }:1                                                   
                                                                                
  Command:                                                                      
          undo dba-threshold 1

System Response

  • The system does not display any message after the queue threshold is configured or deleted successfully in the DBA queue set of the ONT line profile.

More blog:
Posted by at No comments:
Labels: , ,

Wednesday, December 14, 2016

GPON Global Parameter Configuration about display tcont auto-combine state

Function

This command is used to query the status of the T-CONT auto-combine function. When you need to use the T-CONT auto-combine function, run this command to query whether this function is enabled or not.

Format

display tcont auto-combine state

Parameters

None

Modes

GPON board, GPBD, GPFD

Level

Operator level

Usage Guidelines

None

Example

To query the status of the T-CONT auto-combine function, do as follows:
huawei#display tcont auto-combine state
 --------------------------------------------------------------
       The state of T-CONT auto-combine switch: disable
 --------------------------------------------------------------

System Response

  • The system displays the queried result when the command runs successfully.
  • The following table describes the parameters in response to the display tcont auto-combine state command.
    Parameter Description
    The state of T-CONT auto-combine switch Indicates the status of the T-CONT auto-combine function, including enable and disable.
More related:
Posted by at No comments:
Labels: , ,

Monday, December 12, 2016

GEM Port Management about display statistics gemport

Function

This command is used to query the performance statistics of all service-ports attached to a GEM port on the ONT, including the number of upstream or downstream frames, the number of upstream or downstream bytes, and the number of upstream or downstream discarded frames. When you need to query the statistics for the transmitted and received packets at all service-ports attached to a GEM port on the ONT and plan bandwidth assignment accordingly, run this command.

Format

In distributed mode and gigabit-capable passive optical network (GPON) mode:
display statistics gemport portid gemport-id
In distributed mode and privilege mode:
display statistics gemport frameid/slotid portid gemport-id
In profile mode and GPON mode:
display statistics gemport portid ontid gemindex gemindex
In profile mode and privilege mode:
display statistics gemport frameid/slotid portid ontid gemindex gemindex

Parameters

Parameter Description Value
frameid/slotid Indicates the shelf ID and slot ID. Enter "/" between the shelf and slot IDs. Please see Differences Between Shelves.
portid Indicates the ID of the GPON port where the performance statistics are performed. Please see Differences Between Shelves.
ontid Indicates the ID of the ONT port that the GEM port whose performance statistics are to be queried is connected to. This parameter is available only in profile mode. Numeral type. Range: varies with the board type.
gemport-id Indicates the ID of the GEM port to be queried. This parameter is available only in distributed mode. Numeral type. Range: 128-3999.
gemindex gemindex Indicates the ID of the GEM whose performance statistics are to be queried. This parameter is available only in profile mode. Numeral type. Range: 0-1023.

Modes

Privilege mode, GPON mode, GPBD,GPFD

Level

Operator level

Usage Guidelines

Run the config command to enter global config mode, and then run the interface gpon command to enter GPON mode.

Example

In distributed mode and GPON mode, to query the performance statistics of all service-ports attached to GEM port 128 on GPON port 0/3/0 in distributing mode, do as follows:
huawei(config-if-gpon-0/3)#display statistics gemport
{ portid<U><0,7> }:0                                                            
{ gemport-id<U><128,3999> }:128
                                                                                
  Command:                                                                      
          display statistics gemport 0 128                                      
  -------------------------------------------------------------------           
  Upstream frames:                   0                                          
  Upstream bytes:                    0                                          
  Upstream discarded frames:         0                                          
  Downstream frames:                 0                                          
  Downstream bytes:                  0                                          
  Downstream discarded frames:       0                                          
  -------------------------------------------------------------------
In profile mode and GPON mode, to query the performance statistics of all service-ports attached to GEM port 0 on GPON port 0/3/0 in profile mode, do as follows:
huawei(config-if-gpon-0/3)#display statistics gemport
{ portid<U><0,7> }:0 
{ ontid<U><0,63> }:0 
{ gemindex<K> }:gemindex 
{ gemindex<U><0,1023> }:0 
                                                                                
  Command:                                                                      
          display statistics gemport 0 0 gemindex 0                                      
  -------------------------------------------------------------------           
  Upstream frames:                   0                                          
  Upstream bytes:                    0                                          
  Upstream discarded frames:         0                                          
  Downstream frames:                 0                                          
  Downstream bytes:                  0                                          
  Downstream discarded frames:       0                                          
  -------------------------------------------------------------------
In distributed mode and privilege mode, to query the performance statistics for all service-ports attached to GEM port 128 that is connected to GPON port 0/3/0, do as follows:
huawei(config)#display statistics gemport
{ frameid/slotid<S><Length 3-15> }:0/3
{ portid<U><0,15> }:0                                                            
{ gemport-id<U><128,3999> }:128
                                                                                
  Command:                                                                      
          display statistics gemport 0/3 0 128                                      
  -------------------------------------------------------------------           
  Upstream frames                   :0                                          
  Upstream bytes                    :0                                          
  Upstream discarded frames         :0                                          
  Downstream frames                 :0                                          
  Downstream bytes                  :0                                          
  Downstream discarded frames       :0                                          
  -------------------------------------------------------------------
In profile mode and privilege mode, to query the performance statistics for all service-ports attached to GEM port 128 that is connected to GPON port 0/3/0, do as follows:
huawei(config)#display statistics gemport
{ frameid/slotid<S><Length 3-15> }:0/3    
{ portid<U><0,15> }:0
{ ontid<U><0,127> }:1                                                           
{ gemindex<K> }:gemindex                                                        
{ gemindex<U><0,1023> }:128                                   
                                                                                
  Command:                                                                      
          display statistics gemport 0/3 0 1 gemindex 128                                      
  -------------------------------------------------------------------           
  Upstream frames                   :0                                          
  Upstream bytes                    :0                                          
  Upstream discarded frames         :0                                          
  Downstream frames                 :0                                          
  Downstream bytes                  :0                                          
  Downstream discarded frames       :0                                          
  -------------------------------------------------------------------

System Response

  • The system displays the queried result when the command runs successfully.
  • The following table describes the parameters in response to this command. In the upstream direction, the OLT receives packets from the ONT; in the downstream direction, the OLT sends packets to the ONT.
    Parameter Description
    Upstream frames Indicates the number of the upstream frames.
    Upstream bytes Indicates the number of the upstream bytes.
    Upstream discarded frames Indicates the number of the upstream discarded frames.
    Downstream frames Indicates the number of the downstream frames.
    Downstream bytes Indicates the number of the downstream bytes.
    Downstream discarded frames Indicates the number of the downstream discarded frames.

More related:
Posted by at No comments:
Labels: , ,

GEM Port Management about display ont multicast gemport

Function

The command is used to query T-CONTs and port mapping attributes for ONT multicast GEM ports.

Format

display ont multicast gemport portid ontid

Parameters

Parameter Description Value
portid Indicates the ID of the GPON port. Please see Differences Between Shelves.
ontid Indicates the ID of the ONT port. Numeral type. Range: varies with the board type.

Modes

GPON mode, MA5683T, GPBD

Level

Operator level

Usage Guidelines

Run the config command to enter global config mode, and then run the interface gpon command to enter GPON mode.

Example

To set query the GEM port attributes for ONT 0 connected to GPON port 0/3/0, do as follows:
huawei(config-if-gpon-0/3)#display ont multicast gemport                           
{ portid<U><0,7> }:0 
{ ontid<U><0,63> }:0 
                                                                                
  Command:                                                                      
          display ont multicast gemport 0 0 
  ------------------------------------------------------------------------------
  F/S/P              : 0/3/0                                                    
  ONT-ID             : 0                                                        
  T-CONT ID          : 5                                                        
  Bundle ID          : 1                                                        
  ONT port ID        : -                                                        
  ------------------------------------------------------------------------------

System Response

  • The system displays the queried result when the command runs successfully.
  • The following table describes the parameters in response to the command.
    Parameter Description
    T-CONT ID Indicates the T-CONT ID.
    Bundle ID Indicates the bundle ID.
    ONT port ID Indicates the ONT port ID.
More related:
Posted by at No comments:
Labels: , ,

Friday, December 9, 2016

Common ONT Management about clear statistics ont-line-quality

Function

This command is used to clear the line quality statistics of an optical network terminal (ONT). Before collecting the line quality statistics of an ONT within a period of time, ensure that the original line quality statistics of the ONT are reset to zero. The items that can be queried by running the display statistics ont-line-quality command. After the performance statistics are cleared, the system collects the line quality performance statistics again.
NOTE:
  • The line quality performance statistics of the ONT cannot be restored after being cleared. Confirm the action before using the command.
  • This function can also be implemented by the reset statistics ont-line-quality command. Furthermore, its enhanced function will be implemented through the reset statistics ont-line-quality command. Therefore, it is recommended that you run the reset statistics ont-line-quality command.

Format

clear statistics ont-line-quality portid [ ontid ]

Parameters

Parameter Description Value
portid Indicates the ID of the PON port to which the line quality whose performance statistics are to be cleared belongs. Please see Differences Between Shelves.
ontid
Indicates the ID of the ONT port to which the line quality whose performance statistics are to be cleared belongs.
  • If you do not specify the ONT ID, the line quality statistics of all the ONTs connected to a PON port are cleared.
  • If you specify the ONT ID, the line quality statistics of the specified ONT connected to a PON port are cleared.
 Numeral type. Range: varies with the board type.

Modes

GPON mode, EPON mode, GPBD

Level

Operator level

Usage Guidelines

  • Run the config command to enter global config mode, and then run the interface gpon command to enter GPON mode, or run the interface epon command to enter EPON mode.
  • Run the display statistics ont-line-quality command to check whether the line quality statistics are cleared.

Example

To clear the line quality statistics of all ONTs under GPON port 0/3/0, do as follows:
huawei(config-if-gpon-0/3)#clear statistics ont-line-quality                    
{ portid<U><0,7> }:0           
{ <cr>|ontid<U><0,63> }:        
                                                                                
  Command:                                                                      
          clear statistics ont-line-quality 0
To clear the line quality statistics of ONT 0 under GPON port 0/3/0, do as follows: 
huawei(config-if-gpon-0/3)#clear statistics ont-line-quality                    
{ portid<U><0,7> }:0     
{ <cr>|ontid<U><0,63> }:0       
                                                                                
  Command:                                                                      
          clear statistics ont-line-quality 0 0

System Response

  • The system does not display any messages after the line quality statistics of the ONT are cleared successfully.
More related:
Posted by at No comments:
Labels: , ,

Common ONT Management(clear statistics ont)

Function

This command is used to clear the performance statistics of an online optical network terminal (ONT). Before collecting the performance statistics of an ONT within a period of time, ensure that the original statistics of the ONT are reset to zero. The items that can be queried by running the display statistics ont command. After the performance statistics are cleared, the system collects the performance statistics again.
NOTE:
  • The performance statistics of the ONT cannot be restored after being cleared. Confirm the action before using the command.
  • This function can also be implemented by the reset statistics ont command. Furthermore, its enhanced function will be implemented through the reset statistics ont command. Therefore, it is recommended that you run the reset statistics ont command.

Format

clear statistics ont portid ontid

Parameters

Parameter Description Value
portid Indicates the ID of the PON port to which the ONT whose performance statistics are to be cleared belongs. Please see Differences Between Shelves.
ontid Indicates the ID of the ONT whose performance statistics are to be cleared. Numeral type. Range: varies with the board type.

Modes

GPON mode, EPON mode, GPBD

Level

Operator level

Usage Guidelines

  • Run the config command to enter global config mode, and then run the interface gpon command to enter GPON mode, or run the interface epon command to enter EPON mode.
  • To switch the xPON mode, run the diagnose command in privilege mode or global config mode to enter diagnose mode, and then run thexpon mode switch-to command. After the switching, reset the device for the mode to take effect.
  • Run the display ont info command to query the state of ONT.
  • This comand is used to clear the performance statistics of all the ONT ports. You can run the reset statistics ont-eth command to clear the performance statistics of the ONT Ethernet port, and run the reset statistics ont-iphost(gpon) command to clear the performance statistics of the ONT IPHOST port.

Example

To clear the performance statistics of ONT 0 connected to GPON port 0/3/0, do as follows:
huawei(config-if-gpon-0/3)#clear statistics ont
{ portid<U><0,7> }:0
{ ontid<U><0,63> }:0

  Command:
          clear statistics ont 0 0

System Response

  • The system does not display any message after after the performance statistics of an ONT connected to a GPON port are cleared successfully.

More related:
Posted by at No comments:
Labels: , ,

Wednesday, December 7, 2016

The Key Technologies of OLT board

This topic introduces the key technologies of the product.
Prominent Network Protection Function

  •  Supports the MSTP protocol, featuring the loop protection function.
  • Supports the RRPP protocol, implementing rapid switching in a ring network.
  • Supports the LACP and inter-board aggregation features, increasing the bandwidth and

providing the protection function.

  • Supports bidirectional forwarding detection (BFD), improving the reliability of IP applications (such as real-time voice service) and providing support to the network stability for service providers.
  • Supports the smart link application, which implements the redundancy backup and quick migration of active and standby links, ensuring the high reliability and high-speed convergence.
  • Supports Type B redundancy protection for the GPON, ensuring that the services are not interrupted when the backbone optical fiber is faulty.
  • Supports GPON(GPBD) Type C redundancy protection, improving the device reliability.

Superior QoS Function
The superior QoS can guarantee an expected service level with respect to bandwidth, latency,
jitter, and packet loss in a communication network.

  • Tags the data and network management streams with different ToS/DSCP priorities, thereby providing a prioritized forwarding mechanism based on Layer 3
  • Tags the data and network management streams with different 802.1p priorities, thereby providing a prioritized forwarding mechanism based on Layer 2
  • Supports Layers 2-7 traffic classification based on the port, VLAN, MAC address, IP address, TCP port number, or UDP port number.
  • Supports priority control (based on the port, MAC address, IP address, TCP port number, or UDP port number), priority mapping and modification based on the ToS field and 802.1p, and DSCP differentiated services
  • Supports bandwidth control (based on the port, MAC address, IP address, TCP port number or UDP port number) with a control granularity of 64 kbit/s
  • Supports three queue scheduling modes: priority queue (PQ), weighted round robin (WRR), and PQ+WRR.
  • Supports the following QoS capabilities based on the flow rule:
           – Packet filtering
               – Redirect
                 – Mirror
                   – Traffic statistics collection
                     – Traffic shaping
                       – Bandwidth control
                         – Priority tag
              • Supports hierarchical quality of service (HQoS), which guarantees the multi-service
              • bandwidths for multiple users: The first level guarantees the user bandwidths, and the
              • second level guarantees the bandwidths for the services of each user. This ensures that the
              • guaranteed bandwidths absolutely pass and the burst bandwidths pass fairly.
              IPv6
              IPv6 radically solves the problem of IP address shortage. Moreover, IPv6 has the following advantages: It is easy to deploy, compatible with various applications, easy for IPv4 networks to transit to IPv6 networks.
              • Supports the IPv6 address management and assignment.
              • Supports the IPv6 stack and IPv6 host function.
              • Supports the IPv6 route.
              • Supports the IPv6 QoS and security, guarantee the security of the IPv6 network.
              • Supports the IPv6 layer 2 transparent transmission.
              • Supports the IPv6 multicast. By using IPv6 multicast technologies, the network device can
              • manage, control, and forward IPv6 video services and in this way meets carriers'
              • requirements for provisioning IPv6 video services.

              Green and Power Conservation
              The MA5600T/MA5603T meets the efficiency requirements of the European Commission CoC(Code of Conduct). The energy-efficient design ensures quiet operation and optimal heat dissipation, reduces the impact on the environment, and lowers operational costs.
              • Uses chipsets with the highest density and integration in the industry.
              • Uses high-density hardware to improve port energy efficiency.
              • Supports independent shutdown for service ports.
              • Supports manual power-on or power-off for service boards. (A faulty board can be remotely
              • powered off using the CLI or NMS in the equipment room of a site.)
              • Supports refined board power saving.
              • Supports stepless speed adjustment for fans based on component temperature.
              • Supports fan speed control through host software.
              • Supports L2 low-power consumption and L3 standby status for digital subscriber line
              • (DSL) service ports.
              • Automatically shuts down vectoring components when the vectoring function is disabled.
              • Automatically starts the vectoring components when the vectoring function is enabled.
              • These functions dynamically reduce power consumption.
              More relations:

              How to Use the Multimeter to Check Whether the A32 Board Is Faulty?

              Due to disabling TDC-ADJUSTENABLE function high Bit errors on NS3 card


              Posted by at No comments:
              Labels: , ,
              Subscribe to: Posts (Atom)